Security and monitoring

False alarms and how to avoid them

Nearly every false alarm has an ordinary cause, and nearly all of them can be prevented. A system that cries wolf gets switched off, and a system that is switched off protects nobody.

Topic
Security
Reading time
About 5 minutes
Updated
Related service
Security & Monitoring

The short version

  • Most false alarms are caused by people, not by faulty equipment.
  • Give every person their own code and show them how to cancel.
  • When the monitoring center calls, answer and give your passcode.
  • A sensor that false-alarms twice has a reason. Have it looked at.

Why it is worth the trouble

A false alarm costs more than embarrassment. Each one that reaches a dispatcher sends a police car or a fire truck to a house where nothing is wrong. Many cities and counties respond to that by requiring alarm owners to register, and some charge for repeated false alarms at the same address. Memphis, for instance, registers alarms through its Metro Alarm Office. The rules and any charges are set locally, so check with your own city or county for what applies to you.

The larger cost is trust. After the third false alarm in a month, people stop arming the system, and a neighbor who has heard the siren four times stops looking up. Prevention keeps the alarm meaning something.

Cause one: people

The most common false alarm is someone with every right to be there who could not disarm in time.

  • The code nobody told them. The house sitter, the cleaner, a relative staying the weekend, a teenager home early.
  • The code they forgot. Usually under pressure, with a siren counting down.
  • The wrong door. Coming in through a door that has no entry delay sets the alarm off at once.
  • Armed with someone still inside. Arming in "away" mode turns on the motion detectors. Whoever is asleep upstairs trips them on the way to the kitchen.
  • Contractors. A plumber or painter left alone in an armed house.

The fixes

  • A code for each person. Give every regular visitor a code of their own, and take it away when it is no longer needed. With a smart lock tied to the alarm, unlocking with a personal code can disarm the system in the same step; see Access Control.
  • Teach the two modes. "Stay" arms the doors and windows and leaves the motion detectors off. "Away" arms everything. Everyone in the house should know which is which.
  • Use the app. You can check whether the system is armed, and disarm it for someone at the door, from wherever you are.
  • Ask for a longer entry delay if the walk from the door to the panel is a rush. That is a setting, and your installer can change it.
  • Show everyone how to cancel. Enter the code, and then answer the phone.

Cause two: pets, and things that move

A motion detector looks for a warm body moving across its view. It does not know a burglar from a Labrador.

  • Pets. Detectors sold as pet-tolerant ignore movement near the floor, up to a stated weight. They work when mounted at the right height and aimed correctly. A cat on the back of the couch or a dog on the stairs is no longer near the floor.
  • Balloons. Foil party balloons drifting on the air from a vent are a well-known cause. Take them out of any room with a motion detector before you arm.
  • Curtains, plants and hanging decorations that move when the heat or air comes on.
  • Heat sources. A detector that faces a heating vent, a fireplace or a window in direct sun can be fooled by a sudden change in temperature.
  • Insects. A spider walking across the lens of a detector looks very large from the inside.

The fixes are about placement and choice of sensor. Move or re-aim the detector, or in a room the pets have the run of, use glass-break detectors and door and window contacts and leave motion detection out of that room. That is a design decision worth making at the start; it is part of what System Design is for.

Cause three: doors and windows that are not quite shut

A door or window contact is a magnet and a switch. When the two halves move apart, the system reads the door as open.

  • A door that does not latch. A back door that is pushed shut but not latched can be sucked open by the wind or by the air handler starting up.
  • Doors that swell and shrink. In a humid summer, wooden doors and frames move. A contact that was lined up in January may be at the edge of its range in August.
  • Loose or rattling windows in an older house during a storm.
  • Garage and shop doors that flex in a strong wind.

Check that doors latch firmly before arming, and if the panel says a door is open when it is shut, have the contact adjusted. Most panels will also tell you when you try to arm with something open. Do not get in the habit of overriding that message.

Cause four: batteries and neglect

  • Low sensor batteries. Wireless sensors run for years on a battery, and then they do not. A sensor with a failing battery can drop off and come back, or report tamper and trouble signals. The panel warns you well in advance. Change the battery when it asks.
  • The panel's backup battery. It wears out too, and an old one can cause trouble signals after a power outage.
  • Dusty smoke detectors. Dust and small insects inside a smoke detector cause false fire alarms. So does a detector too close to a bathroom door or the kitchen. Smoke detectors also have a service life; the date is on the back.
  • Construction. Sanding and sawing dust will set off a smoke detector. Tell your alarm company before work starts so the detectors can be protected or the system put on test.

The minute after it goes off

  1. Disarm with your code. Do not leave the house to get away from the noise.
  2. Answer the phone. The monitoring center will call. Save their number so you recognize it.
  3. Give your verbal passcode and say it was a mistake. If you do not know the passcode, they cannot cancel.
  4. If you missed the call, call them back right away on the number from your alarm company.
  5. Work out what tripped. The panel and the app show which sensor it was. If it was not a person, find the reason.

The full sequence, including what the operator does if nobody answers, is in alarm monitoring explained.

A short list of habits

  • Everyone who has a key has a code and knows the passcode.
  • Doors latched and windows closed before arming.
  • Pets, balloons and anything that moves kept out of rooms with motion detectors, or those rooms set up without them.
  • Low-battery messages acted on the week they appear.
  • The contact list checked once a year.
  • The system tested now and then, with the monitoring center told first.
  • Your alarm company told before construction or remodeling, a new pet or a long trip.

If one sensor keeps causing trouble, that is a service call, not something to live with. If we installed your system, call 901-476-6918 and tell us which sensor it is.

Written by the team at Security Solutions, Inc. in Brighton, Tennessee. General guidance, not a quote for your house: every home is different, and we would rather look at yours than guess.

What we install

The services behind this guide.

Where we work

We install from our office at 139 N Main St in Brighton, within about 100 miles. The service areas page lists every town and about how long the drive is.

Mike and his team at SSI have taken awesome care of us for the last few years. Any time I’ve ever needed to add to my alarm or surround sound or had a question or concern, they’ve taken care of it quick, fast and in a hurry with 0 issues. Won’t be using anyone else.

Chris Schaeffer, Google review 5 years ago

Free quote

Rather talk it through?

Tell us about the house and we will call you back to set up a free visit. Or skip the form and call the office.

901-476-6918

Security Solutions, Inc.
139 N Main St, Brighton, TN 38011
Toll-free 1-888-280-8775

Request a free quote About a minute

We use these details to reply to your request and for nothing else. Privacy